Tell us your thoughts. A few of these standards used by StructurePoint engineering software and services are list below: ACI-350. BS 5896:2012                       High tensile steel wire and strand for the prestressing of concrete, Specification, EN 10138-1                           Pre-stressing steels. Standards: a technical standard is an established norm or requirement. Your email address will not be published. Throughout the succeeding articles, we will go through the content in each of the code and standards necessary in structural designing. SEI Technical Activities Division. These codes serve as a guideline in our design. Structural Engineering Institute advances and serves the structural engineering profession. BS4483:2005                        Steel Fabric for the Reinforcement of Concrete. In fact the tallest building in the world was analyze adopting the UBC-97 code provisions. The documents prepared by a professional group or committee which are believed to be good and proper engineering practices and which contain mandatory requirement. American Concrete Institute (ACI) Ameican Concrete Institute Technical Documents; ACI 318, Building Code Requirements for Structural Concrete; ACI 530/530.1-13, Building Code Requirements and Specifications for Masonry Structures; American Wood Council (AWC) American Wood Council Technical Information ASCE Standards provide technical guidelines for promoting safety, reliability, productivity, and efficiency in civil engineering. The Structural World > Topics > Design Codes & Standards > Design Codes & Standards, thestructuralworld This standard covers code requirements for the structural design, materials selection, and construction of environmental engineering concrete structures. The following are the American design codes and standards that you might be interested in. Membership. To find these, consult the Canadian General Standards Board (CGSB) Catalogue and write down the # and title of the standards e.g. In Structural Engineering, code references and standards are the factors needed to make the design structurally safe and sound. EN 10138-4                           Pre-stressing Steels. The following are the American design codes and standards that you might be interested in. It is superseded multiple times by other codes IBC, ASCE, …. Codes & Standards; Find Codes & Standard; Find a Standard. There’s a lot of code and standards available, according to its uses, but the Codes stated above are the basic code requirements in the structural designing. Hi Peter, UBC-97 is still widely use in some part of the world. In Structural Engineering, code references and standards are the factors needed to make the design structurally safe and sound. February 7, 2018 They also provide guidance for design projects around the world. SEI Futures Fund. Merchandise. BS 4449:2005                       Steel for the reinforcement of concrete, weldable reinforcing steel, bar, coil, and recoiled products. Many of our standards are referenced by model building codes and adopted by state and local jurisdiction. Virtual Events. Feel free to leave a message on the comment form below. Books & Standards. » SkyCiv Releases a new Structural Design and Analysis API, » The Structural Engineer’s Site Inspection Checklists, » Column Design and Check Options in ETABS, » How to Design Spandrel or Coupling Beams in ETABS, » 3 Post Checks Analysis and Design Consideration in Slab using Csi SAFE, ACI 318-11: Building Code Requirements for Structural Concrete and Commentary, Considerations in Design Load Combinations You Never Knew, Guide to Wind Load Analytical Procedure of ASCE 7-10, How Important is the Load Combinations in Structural Design, Duties and Responsibilities of Structural Engineers, 5 Technical Interview Questions for Structural Engineers, Top 5 Structural Engineering Software That You Should Learn, Pile Cap Design Assumptions & Recommendations. All original content on these pages is fingerprinted and certified by, 1997 Uniform Building Code, Vol. Your email address will not be published. SEI Business and Professional Activities Division, © 2020, American Society of Civil Engineers, Recommended Practice for Fiber-Reinforced Polymer Products for Overhead Utility Line Structures, Second Edition, Wood Pole Structures for Electrical Transmission Lines, Design and Performance of Tall Buildings for Wind, ALL Structural Engineering BOOKS & STANDARDS, Construction Research Congress 2020: Safety, Workforce, and Education, Construction Research Congress 2020: Computer Applications, Construction Research Congress 2020: Infrastructure Systems and Sustainability, Access the current edition and follow committee activities, Access my purchased publications and downloads, Make a donation to support ASCE's activities. EN 10138-2                           Pre-stressing steels. More Structural Engineering. BS EN 10025                         Hot rolled products of non-alloy structural steels – Technical Delivery Conditions, BS 8004: 1986                      Code of practice for foundations, BS 8007: 1987                      Code of practice for design of concrete structures for retaining aqueous liquids, BS8102:2009                        Code of practice for protection of below ground structures against water from the ground, EN1992-3:2006                    Design of Concrete Structures – Part 3 Liquid Retaining and Containment Structures. Are you not “flogging a dead horse” with UBC-97? Other design codes and standards are as follows: AISC 303-05                          Code of Standard Practice for Steel Buildings and Bridges, AISC 360-05                          Specification for Structural Steel Buildings, AISC 341-10                          Seismic Provisions for Structural Steel Buildings, CS EN 206-1:2000                Concrete Specification, performance, production and conformity, BS8500-2: 2006                   Complementary British Standard to BS EN 206-1, BS4027: 1996                       Specification for Sulphate Resisting Portland cement, BS6699: 1992                       Specification for ground granulated blast furnace slag for use with Portland cement, BS EN 450-1:2005                Fly Ash for Concrete: Definitions, Specification, and Conformity Criteria. Local Groups. SEI Local Activities Division. CAN/CGSB-12.20-M89: Structural Design of Glass for Buildings. Access the current edition and follow committee activities. Ammann Research Fellowship. ASCE/SEI 7 Minimum Design Loads For Buildings and Other Structures. Find the Standard that applies to your industry and helps you promote safety, reliability, productivity, and efficiency, as it pertains to engineering components or equipment. 2: Structural Engineering Design Provisions, ACI 318-14 Building Code Requirements for Structural Concrete and Commentary, Minimum Design Loads for Buildings and Other Structures, 3rd Printing (Standard ASCE/SEI 7-10), Seismic Analysis: ASCE-7 and IBC 2012 Provisions, Copyright secured by Digiprove © 2018-2019 The Structural World. EN 10138-3                           Pre-stressing steels. Standards, codes, specifications are extremely important - often essential - technical documents in engineering and related technical fields.
2020 structural engineering codes and standards